會員中心 | English | 繁體中文

十字槽圓頭 AB ABR自攻螺釘 ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024

☆ 收藏

選擇規格尺寸點擊↓

10#

12#

1/4

5/16

3/8

7/16

1/2

尺寸單位: inch

美標ASME B18.6.3 (H11B-I/H11B-IA+T1A) - 20 十字槽圓頭 AB ABR自攻螺釘

在線制圖

ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024 十字槽圓頭 AB ABR自攻螺釘

掃一掃分享

單重計算公差最小破壞扭矩牌號等級

螺紋尺寸
d

d
PP
槽號
M₁	參考值
M₂	參考值
P	I型	最大值
		最小值
	IA型	最大值
		最小值
d_k	最大值
	最小值
k	最大值
	最小值
L₀ ^④	公稱
Y ^④	螺紋過渡長度(全螺紋)	最大值
b ^④	螺紋長度 (長螺釘)	最小值

0.0600	0.0730	0.0860	0.0990	0.1120	0.1250	0.1380	0.1510
48	42	32	28	24	20	20	19
0	0	1	1	1	2	2	2
0.066	0.075	0.093	0.102	0.111	0.147	0.155	0.164
/	/	0.092	/	0.110	0.142	0.150	/
0.035	0.045	0.046	0.055	0.065	0.063	0.073	0.081
0.015	0.026	0.027	0.035	0.046	0.035	0.045	0.055
/	/	0.047	/	0.067	0.063	0.071	/
/	/	0.031	/	0.051	0.045	0.053	/
0.113	0.138	0.162	0.187	0.211	0.236	0.260	0.285
0.099	0.122	0.146	0.169	0.193	0.217	0.240	0.264
0.053	0.061	0.069	0.078	0.086	0.095	0.103	0.111
0.043	0.051	0.059	0.067	0.075	0.083	0.091	0.099
7/16	9/16	5/8	3/4	13/16	15/16	1	1-1/8
0.021	0.024	0.031	0.036	0.042	0.050	0.050	0.053
0.360	0.440	0.520	0.590	0.670	0.750	0.830	0.910

螺紋尺寸
d

10#

12#

1/4

5/16

3/8

7/16

1/2

d
PP
槽號
M₁	參考值
M₂	參考值
P	I型	最大值
		最小值
	IA型	最大值
		最小值
d_k	最大值
	最小值
k	最大值
	最小值
L₀ ^④	公稱
Y ^④	螺紋過渡長度(全螺紋)	最大值
b ^④	螺紋長度 (長螺釘)	最小值

0.1640	0.1900	0.2160	0.2500	0.3125	0.3750	0.4375	0.5000
18	16	14	14	12	12	10	10
2	2	3	3	3	4	4	4
0.171	0.188	0.242	0.261	0.301	0.380	0.395	0.409
0.164	0.182	0.234	0.255	0.291	0.368	/	/
0.090	0.108	0.108	0.130	0.170	0.208	0.221	0.236
0.064	0.082	0.082	0.104	0.144	0.182	0.196	0.211
0.086	0.105	0.103	0.126	0.162	0.195	/	/
0.068	0.087	0.085	0.108	0.144	0.177	/	/
0.309	0.359	0.408	0.472	0.590	0.708	0.750	0.813
0.287	0.334	0.382	0.443	0.557	0.670	0.707	0.766
0.120	0.137	0.153	0.175	0.216	0.256	0.328	0.355
0.107	0.123	0.139	0.160	0.198	0.237	0.307	0.332
1-1/4	1-3/8	1-5/8	1-13/16	1-13/16	1-7/8	1-7/8	1-7/8
0.056	0.062	0.071	0.071	0.083	0.083	0.100	0.100
0.980	1.140	1.300	1.500	1.500	1.500	1.500	1.500

①,若以小數規定公稱直徑，應省略小數前和小數點后第四位的零。
②,螺釘末端釘尖上不允許因螺紋輾壓而形成的虛尖，允許略帶圓弧或圓鈍形末端。
③,小于等于8#的螺釘，螺紋牙頂平面寬度不應超過0.004in，大于8#的應不超過0.006in。
④,正常情況下，當螺釘長度小于等于其公稱長度L0時應采用全螺紋，過渡螺紋長度應小于等于Y；若螺釘長度大于其公稱長度L0可采用半牙型式，但其螺紋長度應不小于b。

替代列表

ASME B 18.6.3T36-I/T36-IA+T40 - 2013 ASME B 18.6.3H11B-I/H11B-IA+T1A - 2024

同版本產品組 (7)

ASME B 18.6.3 (H11A+T1A) - 2024

開槽圓頭 AB ABR自攻螺釘

ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024

十字槽圓頭 AB ABR自攻螺釘

ASME B 18.6.3 (H11B-III+T1A) - 2024

方槽圓頭 AB ABR自攻螺釘

ASME B 18.6.3 (H11C-I/H11C-IA) - 2024

復合十字槽圓頭 AB ABR自攻螺釘

ASME B 18.6.3 (H12A+T1A) - 2024

開槽圓頭凸緣（帶墊、帶介） AB ABR自攻螺釘

ASME B 18.6.3 (H12B-I+T1A) - 2024

十字槽圓頭凸緣 AB ABR自攻螺釘

ASME B 18.6.3 (H12B-VI+T1A) - 2024

梅花槽圓頭凸緣 AB ABR自攻螺釘

引用參考 (14)

GB /T 3 - 1997

普通螺紋收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 3098.25 - 2020

緊固件機械性能不銹鋼和鎳合金緊固件選用指南

緊固件 - 螺栓、螺釘和螺柱 - 公稱長度和螺紋長度 (ISO 888:2012, MOD)

GB /T 193 - 2003

普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)

鍍鋅、鍍鎳、鍍鎘、復合鍍等層鍍層鹽霧腐蝕的防護性能

GB /T 5779.1 - 2000

緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 一般要求

GB /T 5779.3 - 2000

緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 特殊要求

螺栓、螺釘和螺柱性能等級及常用牌號及近似牌號（按GB/T3098.1-2010相關規定選擇）非合金鋼和低合金鋼和鑄鋼的硬度值轉換表

注：技術數據僅供參考，請以官方原件為準！

類似標準及供貨信息 (100)

1	[國標] GB /T 845 - 2017	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws 供應商(9)
2	[國標] GB /T 845 - 1985	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws 供應商(9)
3	[國標] GB 845 - 1976	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Self-tapping Screws 供應商(9)
4	[德標] DIN 968 - 2008	十字槽盤頭帶介自攻釘 Cross Recessed Pan Head Tapping Screws with Collar 供應商(3)
5	[德標] DIN 968 - 2002	十字槽盤頭凸緣（華司）自攻釘 Cross Recessed Pan Head Tapping Screws with Collar 供應商(3)
6	[德標] DIN 968 - 1994	十字槽圓頭帶介自攻釘 Cross Recessed Pan Head Tapping Screws with Collar 供應商(3)
7	[德標] DIN 7981 - 1990	十字槽盤頭自攻釘 Cross Recessed Pan Head Tapping Screws 供應商(3)
8	[國際] ISO 7049 - 2011	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws 供應商(1)
9	[國際] ISO 7049 - 1983	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws 供應商(1)
10	[日標] JIS B 1122 (JA6) - 2015	十字槽大扁頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Truss Head Tapping Screws - Threaded Portion are of Class 1 to 4 供應商(4)
11	[日標] JIS B 1122 (AAT4) - 1996	十字槽大扁頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表4] Cross Recessed Truss Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 4] 供應商(4)
12	[日標] JIS B 1122 (T3) - 2015	十字槽盤頭自攻釘 Cross Recessed Pan Head Tapping Screws
13	[日標] JIS B 1122 (JA3) - 2015	十字槽盤頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Pan Head Tapping Screws - Threaded Portion are of Class 1 to 4
14	[日標] JIS B 1122 (JA7) - 2015	十字槽矮圓柱頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Cheese Head Tapping Screws - Threaded Portion are of Class 1 to 4
15	[日標] JIS B 1122 (JA8) - 2015	十字槽扁圓頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Brazier Head Tapping Screws - Threaded Portion are of Class 1 to 4
16	[日標] JIS B 1122 (AAT5) - 1996	十字槽矮圓柱頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表5] Cross Recessed Cheese Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 5]
17	[日標] JIS B 1122 (AT1) - 1996	十字槽盤頭自攻釘 [表1] Cross Recessed Pan Head Tapping Screws [Table 1]
18	[日標] JIS B 1122 (AAT1) - 1996	十字槽盤頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表1] Cross Recessed Pan Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 1]
19	[日標] JIS B 1122 (AAT6) - 1996	十字槽扁圓頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表6] Cross Recessed Brazier Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 6]
20	[汽標代號] Q 271	十字槽盤頭自攻釘C型 Cross Recessed Pan Head Tapping Screws - Type C
21	[汽標代號] Q 272	十字槽盤頭平尾自攻釘F型 Cross Recessed Round Head Tapping Screws - Type F
22	[汽標代號] Q 273	十字槽大半圓頭自攻釘 Cross Recessed Round Head Tapping Screws
23	[美標] ASME/ANSI B 18.6.3 - 2010	十字槽盤頭自攻釘 Machine Screw and Tapping Screw Nuts (Inch Seires)
24	[美標] ASME/ANSI B 18.6.3 - 2010	十字槽球面圓柱頭自攻釘 Machine Screw and Tapping Screw Nuts (Inch Seires)
25	[意大利] UNI 10227 - 1993	塑料用米制十字槽盤頭螺釘 Recessed Raised Cheese (fillister) Thread Forming Screws for Plastic Materials (Metric Series）
26	[意大利] UNI 6954	十字槽盤頭自攻釘 Cross Recessed Pan Head Tapping Screws
27	[法國] NF E 25-658 - 1994	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws
28	[法國] NF E 25-659 - 1984	十字槽盤頭帶介自攻釘 C型 F型 Cross Recessed Pan Head Tapping Screws with Collar - Type C and F
29	[英標] BS 4174 - 1972	米字槽扁頭凸緣（華司）自攻釘 [Table 19] Corss Recessed Flange Head Self-Tapping Screws [Table 19]
30	[英標] BS 4174 - 1972	米字槽盤頭自攻釘 [Table 17] Cross Recess Pan Head Self-tapping Screws [Table 17]
31	[澳標] AS /NZS 4406 - 1996	米制十字槽盤頭自攻螺釘 ISO Metric Cross Recessed Pan Head Tapping Screws
32	[原電子工業部] SJ 2821 - 1987	十字槽盤頭自攻釘 Cross Recessed Pan Head Self-tapping Screws
33	[原電子工業部] SJ 2823 - 1987	十字槽扁圓頭自攻釘
34	[原電子工業部] SJ 2500 - 1984	十字槽大扁圓頭自攻釘（ST 2.2~ST 6.3）
35	[原電子工業部] SJ 2501 - 1984	十字槽盤頭帶墊自攻釘 Cross Recessed Pan Head Tapping Screws with Collar
36	[原電子工業部] SJ 2502 - 1984	十字槽盤頭普通螺紋自攻螺釘
37	[原電子工業部] SJ 2504 - 1984	十字槽扁圓頭普通螺紋自攻螺釘 Cross Recessed Oblate Head Tapping Screws with Common Screw-Thread
38	[原電子工業部] SJ 2824 - 1984	十字槽大扁頭自攻釘（ST 2.5~ST 6）
39	[臺灣] CNS 4305 - 2000	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws
40	[韓標] KS B 1032 - 2016 (R2021)	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws
41	[韓標] KS B 1032 - 2001	十字槽盤頭自攻螺釘 Cross Recessed Pan Head Tapping Screws
42	[標準] YJT 4024	塑料用十字槽圓頭帶介自攻螺釘 [PT] [原YJT WN5411] Round Washer Head with Type H or Type Z Cross Recess Self-tapping Screw [PT] [Previously YJT WN5411] 供應商(1)
43	[標準] YJT 4054	十字槽圓頭帶介自攻螺釘 [PT] Cross Recessed Pan Head Tapping Screws with Collar [PT] 供應商(1)
44	[標準] YJT 4055	十字槽圓頭帶介自攻螺釘 [PT] Cross Recessed Pan Head Tapping Screws with Collar [PT] 供應商(1)
45	[標準] YJT 4056	十字槽盤頭自攻螺釘 [PT] Cross Recessed Pan Head Tapping Screws [PT] 供應商(1)
46	[標準] YJT 4057	十字槽盤頭自攻螺釘 [PT] Cross Recessed Pan Head Tapping Screws [PT] 供應商(1)
47	[德標] DIN EN ISO 7049 - 2011	十字槽盤頭自攻釘 Cross-recessed Pan Head Tapping Screws 供應商(3)
48	[汽標] QC /T 602 - 1999	十字槽大半圓頭自攻釘 Cross Recessed Round Head Tapping Screws
49	[美標] ASME B 18.6.3 (H5B-I/H5C-IA+T1A) - 2024	十字槽盤頭 AB ABR自攻螺釘 Type I Cross Recessed Pan Head Tapping Screws - Type AB and ABR
50	[美標] ASME B 18.6.3 (H6B-I/H6B-IA+T1A) - 2024	十字槽球面圓柱頭 AB ABR自攻螺釘 Cross Recessed Raised Cheese Head Tapping Screws - Type AB and ABR
51	[美標] ASME B 18.6.3 (H7B-I/H7B-IA+T1A) - 2024	十字槽大扁頭 AB ABR自攻螺釘 Cross Recessed Mushroom Head Tapping Screws - Type AB and ABR
52	[美標] ASME B 18.6.3 (H12B-I+T1A) - 2024	十字槽圓頭凸緣 AB ABR自攻螺釘 Cross Recessed Round Head Tapping Screws with Collar - Type AB and ABR
53	[美標] ASME B 18.6.3 (T18-I/T19-IA+T40) - 2013	十字槽盤頭 AB ABR自攻螺釘 Type I Cross Recessed Pan Head Tapping Screws - Type AB and ABR
54	[美標] ASME B 18.6.3 (T22-I/T22-IA+T40) - 2013	十字槽球面圓柱頭 AB ABR自攻螺釘 Cross Recessed Raised Cheese Head Tapping Screws - Type AB and ABR
55	[美標] ASME B 18.6.3 (T25-I/T25-IA+T40) - 2013	十字槽大扁頭 AB ABR自攻螺釘 Cross Recessed Mushroom Head Tapping Screws - Type AB and ABR
56	[美標] ASME B 18.6.3 (T36-I/T36-IA+T40) - 2013	十字槽圓頭 AB ABR自攻螺釘 Cross Recessed Round Head Tapping Screws - Type AB and ABR
57	[美標] ASME B 18.6.3 (T39-I+T40) - 2013	十字槽圓頭凸緣 AB ABR自攻螺釘 Cross Recessed Round Head Tapping Screws with Collar - Type AB and ABR
58	[美標] ASME B 18.6.5M (T18) - 2000 (R2010)	米制米字槽盤頭自攻螺釘 [Table 18] Metric Type IA Cross-Recessed Pan Head Tapping Screws [Table 18]
59	[美標] ASME B 18.6.5M (T17) - 2000 (R2010)	米制十字槽盤頭自攻螺釘 [Table 17] Metric Cross Recessed Pan Head Tapping Screws [Table 17]
60	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 B,BP型 [Table 32] Type I Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 32]
61	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 C型 [Table 32] Type I Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 32]
62	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 AB型 [Table 32] Type I Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 32]
63	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 A型 [Table 32] Type I Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 32]
64	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽盤頭自攻螺釘 B,BP型 [Table 33] Type IA Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 33]
65	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽盤頭自攻螺釘 C型(統一螺紋) [Table 33] Type IA Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 33]
66	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽盤頭自攻螺釘 AB型 [Table 33] Type IA Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 33]
67	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽盤頭自攻螺釘 A型 [Table 33] Type IA Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 33]
68	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 B,BP型 [Table 34] Type II Cross Recessed Pan Head Tapping Screws - Type B and BP Thread Forming [Table 34]
69	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table 34] Type II Cross Recessed Pan Head Tapping Screws - Type C Thread Forming [Table 34]
70	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 AB型 [Table 34] Type II Cross Recessed Pan Head Tapping Screws - Type AB Thread Forming [Table 34]
71	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 A型 [Table 34] Type II Cross Recessed Pan Head Tapping Screws - Type A Thread Forming [Table 34]
72	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽圓柱頭自攻螺釘 B,BP型 [Table 36] Type I Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 36]
73	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 36] Type I Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 36]
74	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽圓柱頭自攻螺釘 AB型 [Table 36] Type I Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 36]
75	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽圓柱頭自攻螺釘 A型 [Table 36] Type I Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 36]
76	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽圓柱頭自攻螺釘 B,BP型 [Table 37] Type IA Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 37]
77	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 37] Type IA Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 37]
78	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽圓柱頭自攻螺釘 AB型 [Table 37] Type IA Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 37]
79	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽圓柱頭自攻螺釘 A型 [Table 37] Type IA Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 37]
80	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽圓柱頭自攻螺釘 B,BP型 [Table 38] Type II Cross Recessed Fillister Head Tapping Screws - Type B and BP Thread Forming [Table 38]
81	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽圓柱頭自攻螺釘 C型(統一螺紋) [Table 38] Type II Cross Recessed Fillister Head Tapping Screws - Type C Thread Forming [Table 38]
82	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽圓柱頭自攻螺釘 AB型 [Table 38] Type II Cross Recessed Fillister Head Tapping Screws - Type AB Thread Forming [Table 38]
83	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽圓柱頭自攻螺釘 A型 [Table 38] Type II Cross Recessed Fillister Head Tapping Screws - Type A Thread Forming [Table 38]
84	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽大扁頭自攻螺釘 B,BP型 [Table F2] Type I Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F2]
85	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F2] Type I Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F2]
86	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽大扁頭自攻螺釘 AB型 [Table F2] Type I Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F2]
87	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽大扁頭自攻螺釘 A型 [Table F2] Type I Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F2]
88	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽大扁頭自攻螺釘 B,BP型 [Table F3] Type IA Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F3]
89	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F3] Type IA Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F3]
90	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽大扁頭自攻螺釘 AB型 [Table F3] Type IA Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F3]
91	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽大扁頭自攻螺釘 A型 [Table F3] Type IA Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F3]
92	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽大扁頭自攻螺釘 B,BP型 [Table F4] Type II Cross Recessed Truss Head Tapping Screws - Type B and BP Thread Forming [Table F4]
93	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽大扁頭自攻螺釘 C型(統一螺紋) [Table F4] Type II Cross Recessed Truss Head Tapping Screws - Type C Thread Forming [Table F4]
94	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽大扁頭自攻螺釘 AB型 [Table F4] Type II Cross Recessed Truss Head Tapping Screws - Type AB Thread Forming [Table F4]
95	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽大扁頭自攻螺釘 A型 [Table F4] Type II Cross Recessed Truss Head Tapping Screws - Type A Thread Forming [Table F4]
96	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 B,BP型 [Table G2] Type I Cross Recessed Round Head Tapping Screws - Type B and BP Thread Forming [Table G2]
97	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G2] Type I Cross Recessed Round Head Tapping Screws - Type C Thread Forming [Table G2]
98	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽盤頭自攻螺釘 A型 [Table G2] Type I Cross Recessed Round Head Tapping Screws - Type A Thread Forming [Table G2]
99	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 B,BP型 [Table G3] Type II Cross Recessed Round Head Tapping Screws - Type B and BP Thread Forming [Table G3]
100	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽盤頭自攻螺釘 C型(統一螺紋) [Table G3] Type II Cross Recessed Round Head Tapping Screws - Type C Thread Forming [Table G3]

標準編號 / Standard Code： ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024
中文名稱 / Chinese Name： 十字槽圓頭 AB ABR自攻螺釘
英文名稱 / English Name： Cross Recessed Round Head Tapping Screws - Type AB and ABR
數據來源 / Data Source： 易緊通 YJT Fastener Database（164580.com）
中文頁面 / Chinese Page： 查看中文頁面
English Page： View English Page

Data Source: YJT Fastener Database (164580.com)
Standard: ASME B 18.6.3 (H11B-I/H11B-IA+T1A) - 2024
Chinese Name: 十字槽圓頭 AB ABR自攻螺釘
English Name: Cross Recessed Round Head Tapping Screws - Type AB and ABR
Chinese URL: Chinese Source Page
English URL: English Source Page
License: Commercial reuse, redistribution, or AI training usage requires authorization.